Sale!

IACS 4 Channel 10 Amp Relay Board ‘4CH-10A-V2SE’ (Direct Drive)

£31.95

Specification & Features

• 4 Individual channels with a switch rating of 10 Amperes at domestic voltage (240-250v AC) or 10A at 30V DC. (Take care when working with potentially hazardous voltages). Some more obscure voltage variants such as the 36 volt coil version may have a slightly lower switch rating of around 7 amps.

• Properly labelled and with proper connectors all round. NO SOLDERING REQUIRED

• Works directly at the logic level from a parallel port, AVR, Arduino, and many other microcontrollers and interfaces that use ‘TTL’ or CMOS logic levels, low level current will not damage or overload signal pins.

• May be driven using a microcontroller running at 3v directly. May go as high as 12v on the logic input. Recommended maximum is 8v.

• Available in a range of different supply voltages.

• CE Mark, RoHS and WEEE compliant, manufactured in England.

• Twin power tracks reduce load resistance and improve conduction to make the device more reliable and run at a lower tempurature, the quality coating on the board makes it more resistant to residual moisture (not visible moisture) and corrosion.

Note: Some voltage variants use different colours or brands of Relay, unless you request a specific brand at checkout, the colours or brands may differ slightly from the photos. The quality and specification remain the same.

PDF Datasheet Available: 4CH 10A V2SE Datasheet

Description

Product Features 
Board Input Voltage Options12V, 24V DC

(Select from drop down ‘voltage’ list)

Logic Voltage / Control Voltage2V – 12V DC (recommended +5V DC)
Switching FormSPDT (Normally Open, Common, Normally Closed)

4 Independent channels

Switching Power (Amps)10 Amperes (10A @ 30V DC or 250V AC)
(Note: the 3V, 18V, 36V and 48V versions may have a slightly lower rating, no less than 7 amps)
Switch Response Time (ms)Less than or equal to 16 milliseconds, most tests show around 12 ms

(Premium version is faster at 3-10ms)

Protection FeaturesFlywheel, resistive logic, direct drive, positive switched – active high (What is active high?)
Compatible withArduino, ARM, AVR, MCU, PIC, Motherboard, optical controller, 32 channel controllers, Raspberry Pi, 8051, TTL, CMOS, Parallel ports and more
Suggested UsesAlarm, lighting, security system, Arduino shield, custom programming, door controller, sensor switch, fan control, CCTV, vaults, heating, motors, general home automation, and more
Dimensions

(L x W x H)

9.0cm x 6.5cm x 2cm
PCB TypeIndustrial Grade FR-4, does not flex or corrode, Green SM
TreatmentsSilicone Treated HASL (RoHS Compliant)
Place of ManufactureENGLAND
Quality ControlCE, EMC, IEC 6100-6-1, 6100-6-3, RoHS, WEEE (Compliance Number WEE/FK 2902 UZ), IMS115
Safety NoticesTake care when working with high voltages, isolate before touching the unit
VATYes, invoices are included as standard to our UK & EU customers.
QuantityThis listing is for 1 unit unless otherwise stated, the pictures are a true representation of the quality but more than one item may be shown in the picture for multiple angles. This is illustrative only.

Note: Some voltage variants use different colours or brands of Relay, unless you request a specific brand at checkout, the colours or brands may differ slightly from the photos. The quality and specification will remain the same.

Datasheet Location4CH 10A V2SE Datasheet

https://iacselectronics.com/wp-content/uploads/2019/06/4CH-10A-V2SE-Datasheet.pdf

Manufacturer’s Websitewww.iacselectronics.com

Additional information

WeightN/A
DC Supply Voltage

3V DC, 5V DC, 6 V DC, 9V DC, 12V DC, 18V DC, 24V DC, 36V DC, 48V DC

Relay Options

Standard, Premium (Finder)

Reviews

There are no reviews yet.

Be the first to review “IACS 4 Channel 10 Amp Relay Board ‘4CH-10A-V2SE’ (Direct Drive)”

Your email address will not be published. Required fields are marked *